Ender 3 V2 BLTouch Firmware Installation Guide by Smith3D [Updated –13 November 2022]

BLTouch Installation

BLTouch Mount

BLTouch Mount for Ender3 V2 – Link here (Use the two screws provided by BLTouch to screw it in.)

Firmware

* Last Update from Jyers has been 1 year ago, Professional Firmware has more features but setup guide maybe different.

The very first thing you should to is go into Control > Advanced and adjust Probe Offset X to -42 & Probe Y Offset -10 (Printed Mount). and Control > Store Setting.

If you are using Creality official BL-Touch set, you have to set it to Probe X Offset -44 & Probe Y Offset -6.

Video Guide by CHEP : https://www.youtube.com/watch?v=TroPjdkSEOY (Video guide doesn’t include manual leveling, do make sure you do manual bed leveling after adjust the z offset)

Unless your system is well tuned, please use the firmware above instead of high speed. Slow Probe & 5 x 5, which is great for first time tuning.

[8th April] As for Smith3D firmware, we have depreciated our firmware & move on to Jyer firmware as it offer much better features & functionality.

For BTT Filament Sensor & Standard Filament sensor, do enable them
inside Control > Advanced > Filament Sensor/Runout Distance

If you have never change your motherboard, it’s 4.2.2 by default

For 4.2.2 5×5 (High Speed) – download here
For 4.2.7 Board 5×5 (High Speed) – download here
For more info regarding this release
For people who’s suffering random probe fails, please refer to the FAQ below for z switch port firmware.

If flashed & auto leveling doesn’t work, please reset configuration (Control > Restore Default) or try to flash again with different filename. If you are getting Black screen, do format your MicroSD Card to FAT32 and rename the firmware & try again.

Older Build (V1.3.5b)

If you are facing issue on newer builds, you may try the older build

What’s BL Touch High Speed Mode?

• The high speed mode probes multiple points without stowing the needle, making it much much faster. But also prone to crashes if your bed is severely slanted. Please make good use of Manual leveling before you try this.

For Ender 3 V2 no bootloader installation is required. Copy the firmware into your SD card and then slot it in, the printer will begin flashing once you reboot it. Do remember that you need a different filename each time you flash a new firmware eg. firmware1.1bin > firmware1.2bin, else the system will ignore it.

For user who would prefer official firmware from Creality, you may check this guide here

Some UI customizations the community has added

Some other features were offered compared to Stock firmware

• Turn on and off display during printing
• PID Autotune Menu
• Change Filament menu
• Adjust probe offset, filament sensor in the menu
• __h__m Time Format Setting

And remember to add “M420 S1” in Cura!

You can also add G29 for Bed Leveling before every prints

Instead of adding the M420 S1 command above. You can replace it with G29 (Place it after G28). G29 basically starts a new round of auto bed leveling , good for users who would prefer a fresh bed leveling before every prints.

Nozzle Crashing Into Bed?

Steps to produce a good leveling

• Once you setup the Probe Offset X & Probe Offset Y, Store Setting and go to Prepare > Auto Home. Make sure your probe is directly at the center of the bed.

• Start with Manual leveling to make sure the bed is leveled as much as you can, by manually adjusting bed spring. This is to reduce the amount of Z compensation ABL will need to apply when printing. Please refer to CHEP’s guide for how you can level your bed with a piece of paper. The firmware has included the buttons needed for printer to go to all 4 corners + center so you don’t have to do it via a gcode print file.
• After the bed is leveled, get a good Z-offset by using the Prepare > Z-Offset. Remember to pre-heat your nozzle while using this as any remaining material stuck on nozzle tip might interfere the result while gauging with A4 paper. This tool will Auto home and then move Z to 0 to show actual Z offset. Prepare a paper to put between nozzle and bed, then try sliding it in and out, Microstep Up/Down & adjust Z offset until you feel a little friction between paper and nozzle. Use Home Z-Axis to double confirm if the z offset is the right one.

• Once you got your Z offset, go to main menu and press “Leveling”. It will probe 5×5 points and save the mesh to your printer.
• Done and start printing!
• Again, it’s very important to heat up nozzle to 180-200 while using Z-offset (if there is PLA in nozzle) Else the Z-offset will vary a lot depending on the leftover material stuck on nozzle tip.

What if you are not getting an accurate Z Offset from the Tool? (Live Adjust Z Offset)

Sometimes moving the Z axis up and down bit by bit might cause a little slippages, which makes the Z-Offset gauging with A4 paper inaccurate.

If you want a better gauging result. We recommend user to adjust Z Offset via Tune during printing

FAQ

Sometimes Probe doesn’t finish during leveling

Solution 1:
Some users has issue with the bltouch port. the trigger signal or ground is not attached properly. Connect the two pin to the z switch stop & flash the firmware below.



Download 2.0.x.17 ZSwitchStop 5×5 Fast Smith3d Marlin Firmware

Solution 2:
Try connect via Pronterface and check what’s the error code returned.

Summary (this reddit link explained in detail)
– Make sure bed not totally out of level, probe may out of reach or nozzle hit the bed first
– Check if your bed is badly warped
– Check if your bltouch pin is bent
– Check the XY axis wheel tension
– Check the Z axis for binding

Solution 3:
There is a resistor fix for this, you can solder a resistor and use the bltouch port.

3D Printer Repair Service by Smith3D

If you are around Kuala Lumpur, Malaysia and would prefer an expert to service your Creality 3D Printer, check out our repair 3D printer service.